//********************************************************************
//  Ver 1.0
//      2021.11.19  1、新建文件。
//********************************************************************
#include	"config.h"

LED_Str	LED_Info;
const	INT8U	LED_Tab[] =
{
    //    0,  0,  0,  0,  0,  0,  0,   0, 0,  0,
    0,	0,	0,	0,	0,	0,	0,	 0,	0,	0,
    0,	0,	1,	1,	1,  2,	2,   3,  4,  5,
    6,  6,  7,  7,  8,  9,  9,   10, 11, 11,
    12, 13, 14, 15, 16, 17, 18,  20, 21, 23,
    24, 26, 28, 30, 32, 34, 37,  39, 42, 45,
    48, 52, 56, 60, 64, 68, 73,  79, 84, 90,
    97, 100, 100, 100, 100, 100, 100, 100, 100, 100,
    //    100,100,100,100,100,100, 100,100,100,100,
};

void	LED_Init(void)
{
    LED_InfoInit();
    LED_GpioInit();
    LED_FlashFreq(LED_FLASH_2HZ);    //未初始化时设置闪烁频率为2Hz
}

#if 0
void	LED_CapDisplay(INT8U Value, INT8U nSec)
{
    LED_OnTime(nSec);

    if((BATT_FLAG_CHG != 0) &&
            (Value == 100))	//2017.5.27 充电电流大于200mA,电量达到100%，强制电量为99%
    {
        Value = 99;
    }

    if (Value == 0xff)
    {
        LED_Set(LED1, LED_OFF);
        LED_Set(LED2, LED_OFF);
        LED_Set(LED3, LED_OFF);
        LED_Set(LED4, LED_OFF);
    }
    else if (Value == 100)
    {
        LED_Set(LED1, LED_ON);
        LED_Set(LED2, LED_ON);
        LED_Set(LED3, LED_ON);
        LED_Set(LED4, LED_ON);
    }
    else if (Value >= 75)
    {
        LED_Set(LED1, LED_ON);
        LED_Set(LED2, LED_ON);
        LED_Set(LED3, LED_ON);
        if(BATT_FLAG_CHG != 0)
        {
            LED_Set(LED4, LED_FLASH);
        }
        else
        {
            LED_Set(LED4, LED_ON);
        }
    }
    else	if(Value >= 50)
    {
        LED_Set(LED1, LED_ON);
        LED_Set(LED2, LED_ON);
        LED_Set(LED4, LED_OFF);
        if(BATT_FLAG_CHG != 0)
        {
            LED_Set(LED3, LED_FLASH);
        }
        else
        {
            LED_Set(LED3, LED_ON);
        }

    }
    else	if(Value >= 25)
    {
        LED_Set(LED1, LED_ON);
        LED_Set(LED3, LED_OFF);
        LED_Set(LED4, LED_OFF);
        if(BATT_FLAG_CHG != 0)
        {
            LED_Set(LED2, LED_FLASH);
        }
        else
        {
            LED_Set(LED2, LED_ON);
        }

    }
#if 0
    else	if(Value >= 20)
    {
        LED_Set(LED2, LED_OFF);
        LED_Set(LED3, LED_OFF);
        LED_Set(LED4, LED_OFF);
        if(BATT_FLAG_CHG != 0)
        {
            LED_Set(LED1, LED_FLASH);
        }
        else
        {
            LED_Set(LED1, LED_ON);
        }

    }
#endif
    else	if(Value >= 1)
    {
        LED_Set(LED2, LED_OFF);
        LED_Set(LED3, LED_OFF);
        LED_Set(LED4, LED_OFF);
        if(BATT_FLAG_CHG != 0)
        {
            LED_Set(LED1, LED_FLASH);
        }
        else
        {
            LED_Set(LED1, LED_ON);
        }
    }
    else
    {
        LED_Set(LED1, LED_FLASH);
        LED_Set(LED2, LED_OFF);
        LED_Set(LED3, LED_OFF);
        LED_Set(LED4, LED_OFF);
    }

#if 0
    //电量非0时闪烁闪烁频率2HZ，电量为0时闪烁频率为0.5HZ
    if(Value != 0)
    {
        LED_FlashFreq(LED_FLASH_2HZ);
    }
    else
    {
        LED_FlashFreq(LED_FLASH_0D5HZ);
    }
#endif
}
#endif

void	LED_Set(INT8U Name, INT8U Sta)
{
    if (Name > LED_NUM_SIZE) //超出范围直接返回
    {
        return;
    }

    ATOMIC_Start();
    LED_Info.Dn[Name].Flag.BYTES = 0;
    switch (Sta)
    {
    case    LED_ON:
        LED_Info.Dn[Name].Dut = 100;
        LED_Info.Dn[Name].Flag.BITS.Sta = 1;
        break;

    case    LED_PWM:
        LED_Info.Dn[Name].Flag.BITS.Pwm = 1;
        break;

    case    LED_FLASH:
        LED_Info.Dn[Name].Flag.BITS.Sta = LED_FLAG_SYNC;
        LED_Info.Dn[Name].Flag.BITS.Flash = 1;
        break;

    default:    //关闭LED
        break;
    }
    ATOMIC_Stop();
}

#ifdef LED_SEG_MODE
void   LED_SegRefresh(void)
{
    LED_Seg1Off();
    LED_Seg2Off();
    LED_Seg3Off();
    LED_Seg1Low();  //2020.10.29 解决非点亮的LED微亮的情况。
    LED_Seg2Low();
    LED_Seg3Low();
#if 0
    if (LED_OnState() == 0)
    {
        //LED_FLAG_SOC = 0;
        //LED_SocCnt = 0;
        return;
    }
#endif

    switch (LED_SegCnt)
    {
    case    1:  //LED1 ON
        LED_D1On();
        break;

    case    2:  //LED2 ON
        LED_D2On();
        break;

    case    3:  //LED3 ON
        LED_D3On();
        break;

    //case    4:  //LED4 ON
    //    LED_D4On();
    //    break;

    default:    //LED0 ON
        LED_D4On();
        LED_SegCnt = 0;
        break;
    }
    LED_SegCnt++;
}
#endif

#if 0
void    LED_SocDisplay(void)
{
    switch(LED_SocStep)
    {
    case 0:
        LED_FLAG_ON = 1;
        LED_FLAG_SOC = 1;              //显示电量标志
#if 0
        if(BATT_Rsoc > 10)
        {
            LED_Set(LED0, LED_OFF);
            LED_Set(LED1, LED_ON);
        }
        else
        {
            LED_Set(LED0, LED_ON);
            LED_Set(LED1, LED_OFF);
        }
#endif
        if(BATT_Rsoc < 5)
        {
            LED_SocStep = 9;
        }
        LED_Set(LED1, LED_ON);
        LED_Set(LED2, LED_OFF);
        LED_Set(LED3, LED_OFF);
        LED_Set(LED4, LED_OFF);
        break;

    case 2:
        if(BATT_Rsoc <= 25)	//2019.1.5 修改电量流水显示，只显示到电量位灯
        {
            LED_SocStep = 9;
        }
        else
        {
            LED_Set(LED2, LED_ON);
        }
        break;

    case 4:
        if(BATT_Rsoc <= 50)
        {
            LED_SocStep = 9;
        }
        else
        {
            LED_Set(LED3, LED_ON);
        }
        break;

    case 6:
        if(BATT_Rsoc <= 75)
        {
            LED_SocStep = 9;
        }
        else
        {
            LED_Set(LED4, LED_ON);
        }
        break;

    case 8:
        if(BATT_Rsoc <= 75)
        {
            LED_SocStep = 9;
        }
        else
        {
            LED_Set(LED4, LED_ON);
        }
        break;

    case 10:
    case 14:
    case 18:
        //if(SBS_Soc > 10)
        LED_CapDisplay(0xff, 3);
        break;

    case 12:
    case 16:
    case 20:
        LED_CapDisplay(BATT_Rsoc, 3);
        //LED_Set(LED0, LED_ON);
        break;

    case 22:
        BATT_State = SYS_STA_ON;
        LED_FLAG_SOC = 0;
        LED_SocStep = 0;
        LED_FLAG_ON = 0;           //2018.11.30 增加USB输出电量3秒显示一次，增加标志位
        if(LED_FLAG_OFF != 0)
        {
            LED_FLAG_OFF = 0;
            //BATT_STATE=SYS_STA_SLEEP;
            LED_OnTime(0);               //显示时间1秒
        }

        if(BATT_Rsoc < 5)    //电量低于10%，提示电量低10秒
        {
            BATT_SleepDelayTime(6);     //延时5秒进入休眠
            BATT_FLAG_SOC = 2;
            LED_OnTime(5);				//显示时间5秒
            if(LED_FLAG_CRGOFF == 0)
            {
                LED_OnTime(5);				//显示时间5秒
            }
            else
            {
                LED_OnTime(3);				//显示时间0秒
            }
        }

        break;

    default:
        break;
    }
}
#endif

#if 0
//LED显示刷新程序，刷新时基10mS
code INT8U LED_Tab[] = {0x00, 0x01, 0x03, 0x07};
void    LED_Marquee(INT8U Value)
{
    if(LED_Buff[2] < 5)
    {
        LED_Buff[2]++;
        return;
    }
    LED_Buff[2] = 0;

    if(LED_Mask & 0x04) //检测最高位是否为1
    {
        if(Value > 98)  //电量转化为
        {
            //LED_Buff[0]=3;
            LED_Buff[1] = LED_Tab[3];
        }
        else if(Value > 50)
        {
            //LED_Buff[0]=2;
            LED_Buff[1] = LED_Tab[2];
        }
        else if(Value > 20)
        {
            //LED_Buff[0]=1;
            LED_Buff[1] = LED_Tab[1];
        }
        else
        {
            //LED_Buff[0]=0;
            LED_Buff[1] = LED_Tab[0];
        }

        LED_Mask = LED_Buff[1];
        if(PACK_FLAG_STA != STA_CHG)
        {
            LED_FLAG_CHG = 0;
        }
    }
    else
    {
        LED_Mask <<= 1;
        LED_Mask |= 0x01;
        LED_Buff[1] |= LED_Mask;
    }

    if(LED_Buff[1] & 0x01)
    {
        LED_Set(LED0, LED_ON);
    }
    else
    {
        LED_Set(LED0, LED_OFF);
    }

    if(LED_Buff[1] & 0x02)
    {
        LED_Set(LED1, LED_ON);
    }
    else
    {
        LED_Set(LED1, LED_OFF);
    }

    if(LED_Buff[1] & 0x04)
    {
        LED_Set(LED2, LED_ON);
    }
    else
    {
        LED_Set(LED2, LED_OFF);
    }
}
#endif

#if 0
void   LED_Display(void)
{
    INT8U i;

    //LED显示延时到后，关闭显示
    if (LED_OnState() == 0)
    {
        //LED_Set(LED0, LED_OFF);
        LED_Set(LED1, LED_OFF);
        LED_Set(LED2, LED_OFF);
        LED_Set(LED3, LED_OFF);
        LED_Set(LED4, LED_OFF);
        //return;
    }
#if 0
    //充电跑马灯显示电量
    if(LED_FLAG_CHG != 0)
    {
        LED_Marquee(BATT_Soc);
    }
#endif
    //LED闪烁
    LED_Cnt ++;

    if (LED_Cnt >= LED_Cycle)     //0.5Hz闪烁
    {
        LED_Cnt = 0;
        for (i = 0; i < LED_NUM_SIZE; i++)
        {
            if (LED_Info.Dn[i].Flag.BITS.Flash != 0) //占空比100，亮
            {
                LED_Info.Dn[i].Flag.BITS.Sta ^= 0x01;
                LED_FLAG_SYNC = LED_Info.Dn[i].Flag.BITS.Sta; //保存最后一下LED的状态标志到同步标志位
            }
        }
    }

    //呼吸灯
    if (LED_FLAG_TURN == 0)  //PWM状态
    {
        if (LED_Dut < 100)
        {
            LED_Dut++;
        }
        else
        {
            LED_FLAG_TURN = 1;
        }
    }
    else
    {
        if (LED_Dut > 0)
        {
            LED_Dut--;
        }
        else
        {
            LED_FLAG_TURN = 0;
        }
    }
#ifdef LED_GPIO_MODE
    if (LED_Info.Dn[LED0].Flag.BITS.Sta != 0) //LED0
    {
        LED0_On();
    }
    else
    {
        LED0_Off();
    }

    if (LED_Info.Dn[LED1].Flag.BITS.Sta != 0) //LED1
    {
        LED_D1On();
    }
    else
    {
        LED_D1Off();
    }

    if(LED_Info.Dn[LED2].Flag.BITS.Sta != 0)  //LED2
    {
        LED_D2On();
    }
    else
    {
        LED_D2Off();
    }

    if(LED_Info.Dn[LED3].Flag.BITS.Sta != 0)  //LED3
    {
        LED_D3On();
    }
    else
    {
        LED_D3Off();
    }
#if 0
    if(LED_Info.Dn[LED4].Flag.BITS.Sta != 0)  //LED4
    {
        LED_D4On();
    }
    else
    {
        LED_D4Off();
    }
#endif
#endif
}

#endif