; --------------------------------------------------------------------------------
; @Title: eMMC FLASH Programming script for STM32F207
; @Description:
; eMMC FLASH(Numonyx, NAND16GXH) is connected
;
; Internal SRAM: 0x20000000
;
; SD/MMC Controller Register : 0x40012C00      
;
; @Author: jjeong
; @Chip: STM32F207ZG
; @Keywords: Numonyx NAND16GXH eMMC
; @Copyright: (C) 1989-2019 Lauterbach GmbH, licensed for use with TRACE32(R) only
; --------------------------------------------------------------------------------
; $Id: stm32f207-emmc.cmm 7602 2019-11-05 15:02:25Z bschroefel $

LOCAL &arg1
ENTRY &arg1
&arg1=STRing.UPpeR("&arg1")  // for example "PREPAREONLY"


SYStem.CPU stm32f207zg
SYStem.Up

GOSUB board_init

//clk enable for GPIO & SDIO
PER.Set.simple SD:0x40023844 %Long 0x800  
PER.Set.simple SD:0x40023864 %Long 0x75f33

//SDIO pin configuration
PER.Set.simple SD:0x40023830 %Long 0x4001CC ;gpio_c
PER.Set.simple SD:0x40020800 %Long 0x2aa4000 
PER.Set.simple SD:0x40020808 %Long 0x1558000
PER.Set.simple SD:0x4002080C %Long 0x554000 
PER.Set.simple SD:0x40020824 %Long 0xCCCCC  ;sdio_clk, sdio_d0

PER.Set.simple SD:0x40020C00 %Long 0x20   ;gpio_d
PER.Set.simple SD:0x40020C08 %Long 0x10
PER.Set.simple SD:0x40020C0C %Long 0x10
PER.Set.simple SD:0x40020C20 %Long 0xc00  ;sido_cmd

//SDIO controller configuration
PER.Set.simple SD:0x40012C00 %Long 0x3     ;power on
PER.Set.simple SD:0x40012C24 %Long 0xFFFFFFFF
PER.Set.simple SD:0x40012C28 %Long 0x200
PER.Set.simple SD:0x40012C2C %Long 0x0
PER.Set.simple SD:0x40012C04 %Long 0x176   ;clk 400Khz

  Break.RESet
  FLASHFILE.RESet 
  FLASHFILE.CONFIG  0x40012C00  0x0 0x0 0x0

// FLASHFILE.TARGET <<code range>> <<data range>> <<algorithm file>>
  FLASHFILE.TARGET 0x20000000++0x1fff 0x20004000++0x1fff   ~~/demo/arm/flash/byte/emmc_stm32.bin /KEEP    ;for mmc
; FLASHFILE.TARGET 0x20000000++0x1fff 0x20004000++0x1fff   ~~/demo/arm/flash/byte/emmcsd_stm32.bin /keep  ;for sd

PER.Set.simple SD:0x40012C04 %Long 0x176   ; clk 400Khz
FLASHFILE.GETID
PER.Set.simple SD:0x40012C04 %Long 0x100   ; change clk to 20Mhz

FLASHFILE.DUMP 0x0

//Read mmc Extended CSD registers
; FLASHFILE.getextcsd

//End of the test prepareonly
IF "&arg1"=="PREPAREONLY"
ENDDO


//Erase & Write & Verify
; FLASHFILE.ERASE 0x0--0xFFFFFF  
; FLASHFILE.LOAD  * 0x0 
; FLASHFILE.LOAD  * 0x0   /ComPare

ENDDO

board_init:

//Configure PLL
PER.Set.simple SD:0x40023800 %LE %Long 0x9383 
PER.Set.simple SD:0x40023808 %LE %Long 0x0
PER.Set.simple SD:0x40023800 %LE %Long 0x9383 
PER.Set.simple SD:0x40023804 %LE %Long 0x24003010
PER.Set.simple SD:0x40023800 %LE %Long 0x9383 
PER.Set.simple SD:0x40023808 %LE %Long 0x8000
PER.Set.simple SD:0x40023808 %LE %Long 0x9400
PER.Set.simple SD:0x40023804 %LE %Long 0x5403c19
PER.Set.simple SD:0x40023800 %LE %Long 01039383
PER.Set.simple SD:0x40023808 %LE %Long 0x940A

PER.Set.simple SD:0xE000ED08 %LE %Long 0x08000000  ; Vector table on the flash based

PER.Set.simple SD:0xE000ED0C %Long 0xfa050600
PER.Set.simple SD:0xE000E104 %Long 0x20000

RETURN