; --------------------------------------------------------------------------------
; @Title: Example for flash declaration of NXP LPC18xx Cortex-M3 internal flash.
;
; @Description: 
; Script arguments:
;
;  DO lpc18xx [PREPAREONLY] [CPU=<cpu>]
;
;   PREPAREONLY only declares flash but does not execute flash programming
;
;   CPU=<cpu> selects CPU derivative <cpu>
;
; Example:
;
;   DO ~~/demo/arm/flash/lpc18xx CPU=LPC1857 PREPAREONLY
;
; List of LPC18xx derivatives and their configuration:
;
;   CPU-Type     Flash A  Flash B  EEProm  local SRAM
;                  [kB]     [kB]    [kB]      [kB]
; --------------------------------------------------------------------------------
;   LPC1810           -        -      -        64.
;   LPC1812         512.       -      -        32.
;   LPC1813         256.     256.     -        32.
;   LPC1815         384.     384.     -        32.
;   LPC1817         512.     512.     -        32.
;   LPC1820           -        -      -        96.
;   LPC1822         512.       -      -        32.
;   LPC1823         256.     256.     -        32.
;   LPC1825         384.     384.     -        32.
;   LPC1827         512.     512.     -        32.
;   LPC1830           -        -      -        96.
;   LPC1833         256.     256.    16.       32.
;   LPC1837         512.     512.    16.       32.
;   LPC1850           -        -      -        96.
;   LPC1853         256.     256.    16.       32.
;   LPC1857         512.     512.    16.       32.
;
; Memories:
;
;   256/384/512 kB Flash bank A is located at 0x1A000000
;   256/384/512 kB Flash bank B is located at 0x1B000000
;   0/16 kB EEPROM is located at              0x20040000
;   32/40/96 kB local SRAM is located at      0x10000000
;   40 kB local SRAM is located at            0x10080000
;   16/32 kB AHB SRAM is located at           0x20000000
;   0/16 kB AHB SRAM is located at            0x20008000
;   16 kB AHB ETB SRAM is located at          0x2000C000
;   64 kB ROM is located at                   0x10400000
;
; Code Read Protection (CRP):
;
;   CRP is invoked by programming a specific pattern in flash bank A or B 
;   at offset 0x000002FC.
;
;  Name     Pattern      Description
; --------------------------------------------------------------------------------
;  NO_ISP   0x4E697370   Disables ISP request using the P2_7 pin.
;  CRP1     0x12345678   Access to chip via the JTAG pins is disabled. This mode
;                        allows partial flash update using the following ISP 
;                        commands and restrictions:
;                        • Read Memory command: disabled.
;                        • Copy RAM to Flash command: cannot write to Sector 0.
;                        • Go command: disabled.
;                        • Erase sectors command: can erase any individual sector 
;                          except sector 0 only, or can erase all sectors at once.
;                        • Compare command: disabled. This mode is useful when CRP 
;                          is required and flash field updates are needed but all 
;                          sectors can not be erased. The compare command is  
;                          disabled, so in the case of partial flash updates the   
;                          secondary loader should implement a checksum mechanism 
;                          to verify the integrity of the flash.
;                        • Activate flash bank not allowed.
;  CRP2     0x87654321   This is similar to CRP1 with the following additions:
;                        • Write to RAM command: disabled.
;                        • Copy RAM to Flash: disabled.
;                        • Erase command: only allows erase of all sectors.
;  CRP3     0x43218765   This is similar to CRP2, but ISP entry by pulling P2_7 
;                        LOW is disabled if a valid user code is present in flash 
;                        sector 0. This mode effectively disables ISP override 
;                        using the P2_7 pin. It is up to the user’s application 
;                        to provide for flash updates by using IAP calls or 
;                        by invoking ISP.
;                        CAUTION: If CRP3 is selected, no future factory testing  
;                        can be performed on the device.
;
;  Flash programming commands use 32 bytes of space in the top portion of the
;  on-chip RAM (local SRAM at 0x10080000--0x10089FFFF) for execution.
;
; HINTS:
;
;   Flash clock has to match System Clock Frequency (M3_CLK). 
;   FLASH.CLocK.AUTO can be used for automatic flash clock measurement.
;
;   Boot flash cannot be programmed or erased with builtin flash 
;   algorithm. 
;
;   Data has to be loaded into flash aligned to page boundaries.
;
;   Vector table checksum generation is done by script, so that it 
;   can be used or switched off, as needed.
;
; @Author: WRD
; @Copyright: (C) 1989-2019 Lauterbach GmbH, licensed for use with TRACE32(R) only
; @Chip: LPC18*
; --------------------------------------------------------------------------------
; $Rev: 7602 $
; $Id: lpc18xx.cmm 7602 2019-11-05 15:02:25Z bschroefel $

  LOCAL &parameters &param_prepareonly
  ENTRY %LINE &parameters
  &param_prepareonly=(STRing.SCAN(STRing.UPpeR("&parameters"),"PREPAREONLY",0)!=-1)

  LOCAL &param_cpu
  &param_cpu=STRing.SCANAndExtract(STRing.UPpeR("&parameters"),"CPU=","")

  ; ------------------------------------------------------------------------------
  ; Setup CPU

  IF SYStem.MODE()<5
  (
    SYStem.RESet

    IF "&param_cpu"!=""
      SYStem.CPU &param_cpu
    IF !CPUIS(LPC18*)
      SYStem.CPU LPC18*

    SYStem.CONFIG.DEBUGPORTTYPE JTAG
    SYStem.CONFIG.CONNECTOR MIPI20T
    SYStem.Option.ResBreak OFF

    SYStem.Up
  )

  ; ------------------------------------------------------------------------------
  ; Flash declaration

  FLASH.RESet
  GOSUB FlashDeclaration
  LOCAL &FlashSize
  ENTRY &FlashSize
  IF &FlashSize==0x0
    ENDDO NOFLASH

  ; Flash script ends here if called with parameter PREPAREONLY
  IF &param_prepareonly
    ENDDO PREPAREDONE

  ; ------------------------------------------------------------------------------
  ; Flash programming example

  DIALOG.YESNO "Program flash memory?"
  LOCAL &progflash
  ENTRY &progflash
  IF &progflash 
  (
    ; Example for download 
    FLASH.ReProgram.ALL /Erase
    ; 1. Download file
    Data.LOAD.auto *
    ; 2. Checksum generation
    Data.SUM 0x1A000000--0x1A00001B /Long  ; Calculate checksum of all (other) vectors
    Data.Set 0x1A00001C %Long -Data.SUM()  ; Write the 2's complement in reserved vector's spot
    ; 3. Flash programming
    FLASH.ReProgram.off

    ; Reset device
    SYStem.Down
    SYStem.Up
  )

  ENDDO


; --------------------------------------------------------------------------------
; Flash declaration depending on selected CPU 

FlashDeclaration:
  LOCAL &FlashASize &FlashBSize

  IF CPUIS("LPC18?2")
  (
    &FlashASize=0x80000
    &FlashBSize=0x0
  )
  ELSE IF CPUIS("LPC18?3")
  (
    &FlashASize=0x40000
    &FlashBSize=0x40000
  )
  ELSE IF CPUIS("LPC18?5")
  (
    &FlashASize=0x60000
    &FlashBSize=0x60000
  )
  ELSE IF CPUIS("LPC18?7")
  (
    &FlashASize=0x80000
    &FlashBSize=0x80000
  )
  ELSE IF CPUIS("LPC18?0")
  (
    &FlashASize=0x00
    &FlashBSize=0x00
  )
  ELSE
  (
    PRINT %ERROR "FLASH size of CPU type is unknown"
    ENDDO
  )

  IF &FlashASize>=0x40000
  (
    FLASH.Create 1. 0x1A000000--0x1A00FFFF  0x2000 TARGET Long
    FLASH.Create 1. 0x1A010000--0x1A03FFFF 0x10000 TARGET Long
  )
  IF &FlashASize>=0x60000
    FLASH.Create 1. 0x1A040000--0x1A05FFFF 0x10000 TARGET Long
  IF &FlashASize>=0x80000
    FLASH.Create 1. 0x1A060000--0x1A07FFFF 0x10000 TARGET Long

  IF &FlashBSize>=0x40000
  (
    FLASH.Create 2. 0x1B000000--0x1B00FFFF  0x2000 TARGET Long
    FLASH.Create 2. 0x1B010000--0x1B03FFFF 0x10000 TARGET Long
  )
  IF &FlashBSize>=0x60000
    FLASH.Create 2. 0x1B040000--0x1B05FFFF 0x10000 TARGET Long
  IF &FlashBSize>=0x80000
    FLASH.Create 2. 0x1B060000--0x1B07FFFF 0x10000 TARGET Long

  IF (&FlashASize>0x0)||(&FlashBSize>0x0)
  (
    FLASH.TARGET 0x10000000 0x10001000 0x2000 ~~/demo/arm/flash/long/lpc1800.bin /STACKSIZE 0x200 /FirmWareRAM 0x10089FE0--0x10089FFF
    FLASH.CLocK.AUTO
  )

  RETURN &FlashASize+&FlashBSize