Component documentation

Device - Selection of the TPM device module.
Settings - Common TPM module settings.
- Clock settings - Clock/timing settings of the module.
  - Clock source select - Select one of the three clock sources or No clock option to disable the TPM system.
    This item modifies the CLKSB:CLKSA bits in the TPMxSC register.
    There are 4 modes:
    - No clock - There are no items in this mode.
    - Bus rate clock - There are no items in this mode.
    - Fixed system clock - There are no items in this mode.
    - External source - The following items are displayed in this mode:
      - External clock [MHz] - The property contain frequency value for TPM counter when external clock is selected and supported.
  - Prescaler - Select one of the eight divisor for the TPM clock input.
    This item modifies the PS[0:2] bits in the TPMxSC register.
  - Modulo counter - Value of the TPM modulo counter.
    This item modifies the TPMxMODH and TPMxMODL registers.
  - Period - Period of the counter overflow (for information only).
    This item is influenced by the following properties: Prescaler, Modulo Counter, Center Aligned.
- Channels - Settings of the TPM channels.
  One Item of the list looks like:
  Channel - TPMx Channel
  - Capture/compare device - TPM channel selection.
  - Settings - Common channel 0 settings
    - Mode - This property selects mode as input capture, output compare etc.
      This item modifies the CPWMS:MSnB:MSnA bits in the TPMxCnSC register.
      There are 4 modes:
      - Pin not used - Pin not used
        There are no items in this mode.
      - Input capture - Input capture
        The following items are displayed in this mode:
        
        Input control - This property selects the polarity of the input edge that triggers an input capture event.
        This item modifies the ELSnB:ELSnA bits in the TPMxCnSC.
        
        There are 3 options:
        
        Capture on rising edge only: Capture on rising edge only
        
        Capture on falling edge only: Capture on falling edge only
        
        Capture on rising or falling edge: Capture on rising or falling edge
      - Output compare - Output compare
        The following items are displayed in this mode:
        
        Output action - This property selects the level that will be driven in response to an output compare match.
        This item modifies the ELSnB:ELSnA bits in the TPMxCnSC.
        
        There are 4 options:
        
        Software compare only: Software compare only
        
        Toggle output on compare: Toggle output on compare
        
        Clear output on compare: Clear output on compare
        
        Set output on compare: Set output on compare
        
        Channel compare value - This property contains the compare value for the TPM counter.
        This item modifies the TPMxCnV register.
      - PWM - PWM
        The following items are displayed in this mode:
        
        PWM output action - This property selects the polarity of the PWM output.
        This item modifies the ELSnB:ELSnA bits in the TPMxCnSC.
        
        There are 2 options:
        
        Clear output on compare: High-true pulses
        
        Set output on compare: Low-true pulses
        
        Channel compare value - See previous modes for more details
        
        Channel duty - Value of the PWM channel duty.
        This item is influenced by the following properties: Channel Compare Value, Modulo Counter.
  - Pin - Channel 0 pin settings.
    This item is influenced by the following properties: Mode.
    The following items are available only if the group is enabled (the value is "Used"):
    - Channel pin - Name of the channel 0 pin
    - Pull resistor - Channel 0 pull resistor.
      
      There are 6 options:
      - no pull resistor: Input without pull resistor is required
      - pull up: Input with pull-up resistor is required
      - pull down: Input with pull-down resistor is required
      - pull up or no pull: Input with pull-up resistor is preferred, but no-pull is acceptable
      - pull down or no pull: Input with pull-down resistor is preferred, but no-pull is acceptable
      - autoselected pull: There are no special requirements for pull resistors
  - Interrupt - Interrupt settings of channel 0.
    - Channel Interrupt - Channel 0 interrupt settings
      - Settings only if CPU supports interrupts
        
        Interrupt - Interrupt vector (for information only).
      - Channel Interrupt - Enable/disable channel 0 interrupt.
        This item modifies the CHnIE bits in the TPMxSC register.
      - Settings only if CPU supports interrup priority.
        
        Priority - Priority of the chanell interrupt.
      - Settings only if CPU supports interrupts
        
        ISR name - Name of the interrupt service routine (ISR) invoked by this interrupt vector.
        The user code of the routine should handle all respective interrupt flags correctly.
Pins - Module pins/signals settings.
- External clock source - External clock source input pin.
  This item is influenced by the following properties: Clock Source Select.
  The following items are available only if the group is enabled (the value is "Enabled"):
  - Source pin - Name of the pin used as external clock input.
Interrupts - Interrupts settings of the module.
- Overflow Interrupt - TPM overflow interrupt settings.
  - Settings only if CPU supports interrupts
    - Interrupt - Interrupt vector (for information only).
  - Overflow Interrupt - Enable/disable Overflow interrupt.
    This item modifies the TOIE bits in the TPMxSC register.
  - Settings only if CPU supports interrupt priority.
    - Priority - Priority of the overflow interrupt.
  - Settings only if CPU supports interrupts
    - ISR name - Name of the interrupt service routine (ISR) invoked by this interrupt vector.
      The user code of the routine should handle all respective interrupt flags correctly.
Initialization - Initialization options of the module.
- Enable module - Enable module (for information only).
  This item is influenced by the following properties: Clock source select.

PROCESSOR EXPERT is trademark of Freescale Semiconductor, Inc.
Copyright 1997 - 2010 Freescale Semiconductor, Inc.