Component documentation

Component name - Name of the component.
Device - Selection of the PWMMC device module
Settings - Common PWMMC module settings.
- Clock settings - Clock/timing settings of the module.
  - Prescaler - Set value of the prescaler.
    This item modifies the PRSC[1:0] bits in the PCTL2 register.
  - PWM counter modulus - Set value of counter modulus that determines the maximum count for up/down or up-only counter.
    This item modifies the PMOD register.
  - PWM period - The property shows period of PWM.
    This item is influenced by the following properties: Prescaler, PWM counter modulus.
  - Load frequency value - Set value of load frequency.
    This item modifies the LDFQ[1:0] bits in the PCTL2 register.
  - Settings supported for HC908MR8/MR16/MR32 derivatives only.
    - Deadtime - Deadtime clock settings
      - Deadtime device - Selected PWMMC deadtime device module (for information only).
      - Deadtime value - Set value of the deadtime.
        This item modifies the DEADTM register.
      - Deadtime - The property shows the deadtime (for information only).
        This item is influenced by the following properties: Deadtime value.
  - Channel 1 - Channel 1 clock settings
    - PWM value - Set value of the PWM channel 1 duty cycle.
      HC908LB8: This item modifies the PVAL0 register.
      HC908MR8/16/32: This item modifies the PVAL1 register.
    - PWM duty cycle - Duty cycle value of the PWM channel 1 (for information only).
      This item is influenced by the following properties: PWM value.
  - Channel 2 - Channel 1 clock settings
    - PWM value - Set value of the PWM channel 2 duty cycle.
      HC908LB8: This item modifies the PVAL1 register.
      HC908MR8/16/32: This item modifies the PVAL2 register.
    - PWM duty cycle - Duty cycle value of the PWM channel 2 (for information only).
      This item is influenced by the following properties: PWM value.
  - Settings supported for HC908MR8/MR16/MR32 derivatives only.
    - Channel 3 - Channel 3 clock settings
      - PWM value - Set value of the PWM channel 3 duty cycle.
        This item modifies the PVAL3 register.
      - PWM duty cycle - Duty cycle value of the PWM channel 3 (for information only).
        This item is influenced by the following properties: PWM value.
    - Channel 4 - Channel 4 clock settings
      - PWM value - Set value of the PWM channel 4 duty cycle.
        This item modifies the PVAL4 register.
      - PWM duty cycle - Duty cycle value of the PWM channel 4 (for information only).
        This item is influenced by the following properties: PWM value.
    - Channel 5 - Channel 5 clock settings
      - PWM value - Set value of the PWM channel 5 duty cycle.
        This item modifies the PVAL5 register.
      - PWM duty cycle - Duty cycle value of the PWM channel 5 (for information only).
        This item is influenced by the following properties: PWM value.
    - Channel 6 - Channel 6 clock settings
      - PWM value - Set value of the PWM channel 6 duty cycle.
        This item modifies the PVAL6 register.
      - PWM duty cycle - Duty cycle value of the PWM channel 6 (for information only).
        This item is influenced by the following properties: PWM value.
- Settings supported for HC908MR8/MR16/MR32 derivatives only.
  - Align - Set PWMMC operate in edge-aligned or centered mode.
    This item modifies the EDGE bit in the CONFIG register.
  - Mode - Set PWMMC will be six independent PWMs or three complementary pairs.
    This item modifies the INDEP bit in the CONFIG register.
  - Top side polarity - Set top-side PWM's positive or negative polarity.
    This item modifies the TOPNEG bit in the CONFIG register.
  - Bottom side polarity - Set bottom-side PWM's positive or negative polarity.
    This item modifies the BOTNEG bit in the CONFIG register.
  - Settings supported for HC908MR16/MR32 derivatives only.
    - Current correction - Set current method of correction.
      This item modifies the ISENS[1:0] bits in the PCTL1 register.
      
      There are 3 options:
      - Method 1: for correction is used bits IPOL1, IPOL2 and IPOL3
      - Method 2: for correction is used pins Current sensing pin 1, Current sensing pin 2 and Current sensing pin 3 during deadtime
      - Method 3: for correction is used pins Current sensing pin 1, Current sensing pin 2 and Current sensing pin 3 occurs at the half cycle in center aligned mode and at the end of cycle in edge-aligned mode.
- Settings supported for HC908MR8/MR16/MR32 derivatives only.
  - Output control - Set mode of output pins. If set to Manually option user operates with output pin activity by the hand.
    This item modifies the OUTCTL bit in the PWMOUT register.
- Settings supported for HC908MR8/MR16/MR32 derivatives only.
  - Correction - Correction settings
    - Correction for PWM pair 0 - Select which PWM value register is used for PWM output pins 1 and 2 in complementary mode.
      HC908MR16/32: This item modifies the IPOL1 bit in the PCTL2 register.
      HC908MR8: This item modifies the SEL12 bit in the PCTL2 register.
    - Correction for PWM pair 1 - Select which PWM value register is used for PWM output pins 3 and 4 in complementary mode.
      HC908MR16/32: This item modifies the IPOL2 bit in the PCTL2 register.
      HC908MR8: This item modifies the SEL34 bit in the PCTL2 register.
    - Correction for PWM pair 2 - Select which PWM value register is used for PWM output pins 5 and 6 in complementary mode.
      HC908MR16/32: This item modifies the IPOL3 bit in the PCTL2 register.
      HC908MR8: This item modifies the SEL56 bit in the PCTL2 register.
Pins - Module pins/signals settings.
- Settings supported for HC908MR32 derivatives only.
  - Correction - Correction Pins/Signals
    - Current sensing pin 1 - Selection of current sensing pin 1
    - Current sensing pin 1 signal - Signal of current sensing pin 1
    - Current sensing pin 2 - Selection of current sensing pin 2
    - Current sensing pin 2 signal - Signal of current sensing pin 2
    - Current sensing pin 3 - Selection of current sensing pin 3
    - Current sensing pin 3 signal - Signal of current sensing pin 3
- Channel 1 - Channel 1 Pins/Signals
  - Channel - Selection of PWM channel 1
  - Output pin - Selection of channel 1 output pin
  - Output pin signal - Signal of channel 1 output pin
  - Settings supported for HC908LB8derivatives only.
    - Output pin enable - Enable/disable channel 1 output pin.
      This item modifies the DIS0 bit in the PCTL2 register.
    - Output pin polarity - Set polarity of PWM waveform of PWM channel 1.
      This item modifies the POL0 bit in the PCTL2 register.
  - Settings supported for HC908MR8 derivatives only.
    - Output pin active - Set Channel 1 output pin activated or inactivated. This property is available only if the Output control property is set to manually mode. This item modifies the OUT1 bit in the PWMOUT register.
- Channel 2 - Channel 2 Pins/Signals
  - Channel - Selection of PWM channel 2
  - Output pin - Selection of channel 2 output pin
  - Output pin signal - Signal of channel 2 output pin
  - Settings supported for HC908LB8 derivatives only.
    - Output pin enable - Enable/disable channel 2 output pin.
      This item modifies the DIS1 bit in the PCTL2 register.
    - Output pin polarity - Set polarity of PWM waveform of PWM channel 2.
      This item modifies the POL1 bit in the PCTL2 register.
  - Settings supported for HC908MR8/16/32 derivatives only.
    - Output pin active - Set Channel 2 output pin activated or inactivated. This property is available only if the Output control property is set to manually mode. This item modifies the OUT2 bit in the PWMOUT register.
- Settings supported for HC908MR8/16/32 derivatives only.
  - Channel 3 - Channel 3 Pins/Signals
    - Channel - Selection of PWM channel 3
    - Output pin - Selection of channel 3 output pin
    - Output pin signal - Signal of channel 3 output pin
    - Output pin active - Set Channel 3 output pin activated or inactivated. This property is available only if the Output control property is set to manually mode. This item modifies the OUT3 bit in the PWMOUT register.
  - Channel 4 - Channel 4 Pins/Signals
    - Channel - Selection of PWM channel 4
    - Output pin - Selection of channel 4 output pin
    - Output pin signal - Signal of channel 4 output pin
    - Output pin active - Set Channel 4 output pin activated or inactivated. This property is available only if the Output control property is set to manually mode. This item modifies the OUT4 bit in the PWMOUT register.
  - Channel 5 - Channel 5 Pins/Signals
    - Channel - Selection of PWM channel 5
    - Output pin - Selection of channel 5 output pin
    - Output pin signal - Signal of channel 5 output pin
    - Output pin active - Set Channel 5 output pin activated or inactivated. This property is available only if the Output control property is set to manually mode. This item modifies the OUT5 bit in the PWMOUT register.
  - Channel 6 - Channel 6 Pins/Signals
    - Channel - Selection of PWM channel 6
    - Output pin - Selection of channel 6 output pin
    - Output pin signal - Signal of channel 6 output pin
    - Output pin active - Set Channel 6 output pin activated or inactivated. This property is available only if the Output control property is set to manually mode. This item modifies the OUT6 bit in the PWMOUT register.
- Faults - Faults Pins/Signals
  - Settings supported for HC908LB8 derivatives only.
    - Fault device - Selection device of fault
    - Fault pin - Selection of fault pin.
      This item modifies the FPOS bit in the PCTL1 register.
    - Fault pin signal - Signal of fault pin
    - Fault control - Select between automatic and manual mode faults.
      This item modifies the FMODE bit in the FCR register.
    - Channel 1 fault mode - The property allows user to select PWM channel 1 to be disabled when logic 1 present on fault pin.
      This item modifies the MAP0 bit in the DISMAP register.
    - Channel 2 fault mode - The property allows user to select PWM channel 2 to be disabled when logic 1 present on fault pin.
      This item modifies the MAP1 bit in the DISMAP register
  - Settings supported for HC908MR8/16/32 derivatives only.
    - Fault 1 - Fault 1 Pins/Signals
      - Fault 1 device - Selection device of fault1
      - Fault 1 pin - Selection of fault 1 pin
      - Fault 1 pin signal - Signal of fault 1 pin
      - Fault clearing mode - Select between automatic and manual mode faults.
        This item modifies the FMODE1 bit in the FCR register.
    - Settings supported for HC908MR16/32 derivatives only.
      - Fault 2 - Fault 2 Pins/Signals
        
        Fault 2 device - Selection device of fault2
        
        Fault pin 2 - Selection of fault 2 pin
        
        Fault pin 2 signal - Signal of fault 2 pin
        
        Fault clearing mode - Select between automatic and manual mode faults.
        This item modifies the FMODE2 bit in the FCR register.
      - Fault 3 - Fault 3 Pins/Signals
        
        Fault 3 device - Selection device of fault3
        
        Fault pin 3 - Selection of fault 3 pin
        
        Fault pin 3 signal - Signal of fault 3 pin
        
        Fault clearing mode - Select between automatic and manual mode faults.
        This item modifies the FMODE3 bit in the FCR register.
    - Settings supported for HC908MR8 - 32 pins /32 derivatives only.
      - Fault 4 - Fault 4 Pins/Signals
        
        Fault 4 device - Selection device of fault4
        
        Fault pin 4 - Selection of fault 4 pin
        
        Fault pin 4 signal - Signal of fault 4 pin
        
        Fault clearing mode - Select between automatic and manual mode faults.
        This item modifies the FMODE4 bit in the FCR register.
- Settings supported for HC908MR8/16/32 derivatives only.
  - Pin 1 with bank X - The property sets if Pin 1 is enabled or disabled by Bank X.
    This item modifies the Bit 0 bit in the DISMAP register.
  - Pin 2 with bank X - The property sets if Pin 2 is enabled or disabled by Bank X.
    This item modifies the Bit 1 bit in the DISMAP register.
  - Pin 2 with bank Y - The property sets if Pin 2 is enabled or disabled by Bank Y.
    This item modifies the Bit 2 bit in the DISMAP register.
  - Pin 3 with bank X - The property sets if Pin 3 is enabled or disabled by Bank X.
    This item modifies the Bit 3 bit in the DISMAP register.
  - Pin 4 with bank Y - The property sets if Pin 4 is enabled or disabled by Bank Y.
    This item modifies the Bit 4 bit in the DISMAP register.
  - Pin 5 with bank X - The property sets if Pin 5 is enabled or disabled by Bank X.
    This item modifies the Bit 5 bit in the DISMAP register.
  - Pin 5 with bank Y - The property sets if Pin 5 is enabled or disabled by Bank Y.
    This item modifies the Bit 6 bit in the DISMAP register.
  - Pin 6 with bank Y - The property sets if Pin 6 is enabled or disabled by Bank Y.
    This item modifies the Bit 7 bit in the DISMAP register.
  - Enable pins in bank X - Select yes/no to enable/disable one or more pins in bank X.
    This item modifies the DISX bit in the PCL1 register.
  - Enable pins in bank Y - Select yes/no to enable/disable one or more pins in bank Y.
    This item modifies the DISY bit in the PCL1 register.
Interrupts - Interrupts settings of the module
- Settings supported for HC908LB8 derivatives only.
  - Fault even interrupt - Fault even interrupt settings
    - Interrupt - Interrupt vector (for information only).
    - Fault interrupt - Enable/disable Fault even interrupt.
      This item modifies the FINT bit in the FSR register.
    - ISR name - Name of the interrupt service routine (ISR) invoked by this interrupt vector.
      The user code of the routine should handle all respective interrupt flags correctly. The routine must be implemented in the user code, it is not generated by Processor Expert. Find external prototypes of the ISRs in the component module header file.
- Settings supported for HC908MR8/MR32 derivatives only.
  - Fault even 1 interrupt - Fault even interrupt 1 settings
    - Interrupt - Interrupt vector (for information only).
    - Fault 1 interrupt - Enable/disable Fault even 1 interrupt.
      This item modifies the FINT1 bit in the FSR register.
    - ISR name - Name of the interrupt service routine (ISR) invoked by this interrupt vector.
      The user code of the routine should handle all respective interrupt flags correctly. The routine must be implemented in the user code, it is not generated by Processor Expert. Find external prototypes of the ISRs in the component module header file.
  - Settings supported for HC908MR8 derivatives only.
    - Fault even 2 interrupt - Fault even interrupt 2 settings
      - Interrupt - Interrupt vector (for information only).
      - Fault 2 interrupt - Enable/disable Fault even 2 interrupt.
        This item modifies the FINT2 bit in the FSR register
      - ISR name - Name of the interrupt service routine (ISR) invoked by this interrupt vector.
        The user code of the routine should handle all respective interrupt flags correctly. The routine must be implemented in the user code, it is not generated by Processor Expert. Find external prototypes of the ISRs in the component module header file.
    - Fault even 3 interrupt - Fault even interrupt 3 settings
      - Interrupt - Interrupt vector (for information only).
      - Fault 3 interrupt - Enable/disable Fault even 3 interrupt.
        This item modifies the FINT3 bit in the FSR register.
      - ISR name - Name of the interrupt service routine (ISR) invoked by this interrupt vector.
        The user code of the routine should handle all respective interrupt flags correctly. The routine must be implemented in the user code, it is not generated by Processor Expert. Find external prototypes of the ISRs in the component module header file.
  - Settings supported for HC908MR8 - 32 pins /32 derivatives only.
    - Fault even 4 interrupt - Fault even interrupt 4 settings
      - Interrupt - Interrupt vector (for information only).
      - Fault 4 interrupt - Enable/disable Fault even 4 interrupt.
        This item modifies the FINT4 bit in the FSR register.
      - ISR name - Name of the interrupt service routine (ISR) invoked by this interrupt vector.
        The user code of the routine should handle all respective interrupt flags correctly. The routine must be implemented in the user code, it is not generated by Processor Expert. Find external prototypes of the ISRs in the component module header file.
- PWM interrupt - PWM interrupt settings
  - Interrupt - Interrupt vector (for information only).
  - PWM interrupt - Enable/disable PWM interrupt.
    This item modifies the PWMINT bit in the PCTL1 register
  - ISR name - Name of the interrupt service routine (ISR) invoked by this interrupt vector.
    The user code of the routine should handle all respective interrupt flags correctly. The routine must be implemented in the user code, it is not generated by Processor Expert. Find external prototypes of the ISRs in the component module header file.
Initialization - Initialization options of the module
- Call Init method - The Init method of the component may be called after power-on or reset (in initialization code) by PE.
  yes - The Init method is called by PE
  no - The Init method is not called by PE, it should be called in user's code
- Module enabled - Enable PWMMC module. This item modifies the PWMEN bit in the PCTL1 register

PROCESSOR EXPERT is trademark of Freescale Semiconductor, Inc.
Copyright 1997 - 2010 Freescale Semiconductor, Inc.