Component documentation

Device - Selection of the PWMMC device module
Settings - Common PWMMC module settings.
- Clock settings - Clock/timing settings of the module.
  - Prescaler - Set value of the prescaler.
    This item modifies the PRSC[1:0] bits in the PCTL2 register.
  - PWM counter modulus - Set value of counter modulus that determines the maximum count for up/down or up-only counter.
    This item modifies the PMOD register.
  - PWM period - The property shows period of PWM.
    This item is influenced by the following properties: Prescaler, PWM counter modulus.
  - Load frequency value - Set value of load frequency.
    This item modifies the LDFQ[1:0] bits in the PCTL2 register.
  - Settings supported for HC908MR8/MR16/MR32 derivatives only.
    - Deadtime - Deadtime clock settings
      - Deadtime device - Selected PWMMC deadtime device module (for information only).
      - Deadtime value - Set value of the deadtime.
        This item modifies the DEADTM register.
      - Deadtime - The property shows the deadtime (for information only).
        This item is influenced by the following properties: Deadtime value.
  - Channel 1 - Channel 1 clock settings
    - PWM value - Set value of the PWM channel 1 duty cycle.
      HC908LB8: This item modifies the PVAL0 register.
      HC908MR8/16/32: This item modifies the PVAL1 register.
    - PWM duty cycle - Duty cycle value of the PWM channel 1 (for information only).
      This item is influenced by the following properties: PWM value.
  - Channel 2 - Channel 1 clock settings
    - PWM value - Set value of the PWM channel 2 duty cycle.
      HC908LB8: This item modifies the PVAL1 register.
      HC908MR8/16/32: This item modifies the PVAL2 register.
    - PWM duty cycle - Duty cycle value of the PWM channel 2 (for information only).
      This item is influenced by the following properties: PWM value.
  - Settings supported for HC908MR8/MR16/MR32 derivatives only.
    - Channel 3 - Channel 3 clock settings
      - PWM value - Set value of the PWM channel 3 duty cycle.
        This item modifies the PVAL3 register.
      - PWM duty cycle - Duty cycle value of the PWM channel 3 (for information only).
        This item is influenced by the following properties: PWM value.
    - Channel 4 - Channel 4 clock settings
      - PWM value - Set value of the PWM channel 4 duty cycle.
        This item modifies the PVAL4 register.
      - PWM duty cycle - Duty cycle value of the PWM channel 4 (for information only).
        This item is influenced by the following properties: PWM value.
    - Channel 5 - Channel 5 clock settings
      - PWM value - Set value of the PWM channel 5 duty cycle.
        This item modifies the PVAL5 register.
      - PWM duty cycle - Duty cycle value of the PWM channel 5 (for information only).
        This item is influenced by the following properties: PWM value.
    - Channel 6 - Channel 6 clock settings
      - PWM value - Set value of the PWM channel 6 duty cycle.
        This item modifies the PVAL6 register.
      - PWM duty cycle - Duty cycle value of the PWM channel 6 (for information only).
        This item is influenced by the following properties: PWM value.
- Settings supported for HC908MR8/MR16/MR32 derivatives only.
  - Align - Set PWMMC operate in edge-aligned or centered mode.
    This item modifies the EDGE bit in the CONFIG register.
  - Mode - Set PWMMC will be six independent PWMs or three complementary pairs.
    This item modifies the INDEP bit in the CONFIG register.
  - Top side polarity - Set top-side PWM's positive or negative polarity.
    This item modifies the TOPNEG bit in the CONFIG register.
  - Bottom side polarity - Set bottom-side PWM's positive or negative polarity.
    This item modifies the BOTNEG bit in the CONFIG register.
  - Settings supported for HC908MR16/MR32 derivatives only.
    - Current correction - Set current method of correction.
      This item modifies the ISENS[1:0] bits in the PCTL1 register.
      
      There are 3 options:
      - Method 1: for correction is used bits IPOL1, IPOL2 and IPOL3
      - Method 2: for correction is used pins Current sensing pin 1, Current sensing pin 2 and Current sensing pin 3 during deadtime
      - Method 3: for correction is used pins Current sensing pin 1, Current sensing pin 2 and Current sensing pin 3 occurs at the half cycle in center aligned mode and at the end of cycle in edge-aligned mode.
- Settings supported for HC908MR8/MR16/MR32 derivatives only.
  - Output control - Set mode of output pins. If set to Manually option user operates with output pin activity by the hand.
    This item modifies the OUTCTL bit in the PWMOUT register.
- Settings supported for HC908MR8/MR16/MR32 derivatives only.
  - Correction - Correction settings
    - Correction for PWM pair 0 - Select which PWM value register is used for PWM output pins 1 and 2 in complementary mode.
      HC908MR16/32: This item modifies the IPOL1 bit in the PCTL2 register.
      HC908MR8: This item modifies the SEL12 bit in the PCTL2 register.
    - Correction for PWM pair 1 - Select which PWM value register is used for PWM output pins 3 and 4 in complementary mode.
      HC908MR16/32: This item modifies the IPOL2 bit in the PCTL2 register.
      HC908MR8: This item modifies the SEL34 bit in the PCTL2 register.
    - Correction for PWM pair 2 - Select which PWM value register is used for PWM output pins 5 and 6 in complementary mode.
      HC908MR16/32: This item modifies the IPOL3 bit in the PCTL2 register.
      HC908MR8: This item modifies the SEL56 bit in the PCTL2 register.
Pins - Module pins/signals settings.
- Settings supported for HC908MR32 derivatives only.
  - Correction - Correction Pins/Signals
    - Current sensing pin 1 - Selection of current sensing pin 1
    - Current sensing pin 2 - Selection of current sensing pin 2
    - Current sensing pin 3 - Selection of current sensing pin 3
- Channel 1 - Channel 1 Pins/Signals
  - Channel - Selection of PWM channel 1
  - Output pin - Selection of channel 1 output pin
  - Settings supported for HC908LB8derivatives only.
    - Output pin enable - Enable/disable channel 1 output pin.
      This item modifies the DIS0 bit in the PCTL2 register.
    - Output pin polarity - Set polarity of PWM waveform of PWM channel 1.
      This item modifies the POL0 bit in the PCTL2 register.
  - Settings supported for HC908MR8 derivatives only.
    - Output pin active - Set Channel 1 output pin activated or inactivated. This property is available only if the Output control property is set to manually mode. This item modifies the OUT1 bit in the PWMOUT register.
- Channel 2 - Channel 2 Pins/Signals
  - Channel - Selection of PWM channel 2
  - Output pin - Selection of channel 2 output pin
  - Settings supported for HC908LB8 derivatives only.
    - Output pin enable - Enable/disable channel 2 output pin.
      This item modifies the DIS1 bit in the PCTL2 register.
    - Output pin polarity - Set polarity of PWM waveform of PWM channel 2.
      This item modifies the POL1 bit in the PCTL2 register.
  - Settings supported for HC908MR8/16/32 derivatives only.
    - Output pin active - Set Channel 2 output pin activated or inactivated. This property is available only if the Output control property is set to manually mode. This item modifies the OUT2 bit in the PWMOUT register.
- Settings supported for HC908MR8/16/32 derivatives only.
  - Channel 3 - Channel 3 Pins/Signals
    - Channel - Selection of PWM channel 3
    - Output pin - Selection of channel 3 output pin
    - Output pin active - Set Channel 3 output pin activated or inactivated. This property is available only if the Output control property is set to manually mode. This item modifies the OUT3 bit in the PWMOUT register.
  - Channel 4 - Channel 4 Pins/Signals
    - Channel - Selection of PWM channel 4
    - Output pin - Selection of channel 4 output pin
    - Output pin active - Set Channel 4 output pin activated or inactivated. This property is available only if the Output control property is set to manually mode. This item modifies the OUT4 bit in the PWMOUT register.
  - Channel 5 - Channel 5 Pins/Signals
    - Channel - Selection of PWM channel 5
    - Output pin - Selection of channel 5 output pin
    - Output pin active - Set Channel 5 output pin activated or inactivated. This property is available only if the Output control property is set to manually mode. This item modifies the OUT5 bit in the PWMOUT register.
  - Channel 6 - Channel 6 Pins/Signals
    - Channel - Selection of PWM channel 6
    - Output pin - Selection of channel 6 output pin
    - Output pin active - Set Channel 6 output pin activated or inactivated. This property is available only if the Output control property is set to manually mode. This item modifies the OUT6 bit in the PWMOUT register.
- Faults - Faults Pins/Signals
  - Settings supported for HC908LB8 derivatives only.
    - Fault device - Selection device of fault
    - Fault pin - Selection of fault pin.
      This item modifies the FPOS bit in the PCTL1 register.
    - Fault control - Select between automatic and manual mode faults.
      This item modifies the FMODE bit in the FCR register.
    - Channel 1 fault mode - The property allows user to select PWM channel 1 to be disabled when logic 1 present on fault pin.
      This item modifies the MAP0 bit in the DISMAP register.
    - Channel 2 fault mode - The property allows user to select PWM channel 2 to be disabled when logic 1 present on fault pin.
      This item modifies the MAP1 bit in the DISMAP register
  - Settings supported for HC908MR8/16/32 derivatives only.
    - Fault 1 - Fault 1 Pins/Signals
      - Fault 1 device - Selection device of fault1
      - Fault 1 pin - Selection of fault 1 pin
      - Fault clearing mode - Select between automatic and manual mode faults.
        This item modifies the FMODE1 bit in the FCR register.
    - Settings supported for HC908MR16/32 derivatives only.
      - Fault 2 - Fault 2 Pins/Signals
        
        Fault 2 device - Selection device of fault2
        
        Fault pin 2 - Selection of fault 2 pin
        
        Fault clearing mode - Select between automatic and manual mode faults.
        This item modifies the FMODE2 bit in the FCR register.
      - Fault 3 - Fault 3 Pins/Signals
        
        Fault 3 device - Selection device of fault3
        
        Fault pin 3 - Selection of fault 3 pin
        
        Fault clearing mode - Select between automatic and manual mode faults.
        This item modifies the FMODE3 bit in the FCR register.
    - Settings supported for HC908MR8 - 32 pins /32 derivatives only.
      - Fault 4 - Fault 4 Pins/Signals
        
        Fault 4 device - Selection device of fault4
        
        Fault pin 4 - Selection of fault 4 pin
        
        Fault clearing mode - Select between automatic and manual mode faults.
        This item modifies the FMODE4 bit in the FCR register.
- Settings supported for HC908MR8/16/32 derivatives only.
  - Pin 1 with bank X - The property sets if Pin 1 is enabled or disabled by Bank X.
    This item modifies the Bit 0 bit in the DISMAP register.
  - Pin 2 with bank X - The property sets if Pin 2 is enabled or disabled by Bank X.
    This item modifies the Bit 1 bit in the DISMAP register.
  - Pin 2 with bank Y - The property sets if Pin 2 is enabled or disabled by Bank Y.
    This item modifies the Bit 2 bit in the DISMAP register.
  - Pin 3 with bank X - The property sets if Pin 3 is enabled or disabled by Bank X.
    This item modifies the Bit 3 bit in the DISMAP register.
  - Pin 4 with bank Y - The property sets if Pin 4 is enabled or disabled by Bank Y.
    This item modifies the Bit 4 bit in the DISMAP register.
  - Pin 5 with bank X - The property sets if Pin 5 is enabled or disabled by Bank X.
    This item modifies the Bit 5 bit in the DISMAP register.
  - Pin 5 with bank Y - The property sets if Pin 5 is enabled or disabled by Bank Y.
    This item modifies the Bit 6 bit in the DISMAP register.
  - Pin 6 with bank Y - The property sets if Pin 6 is enabled or disabled by Bank Y.
    This item modifies the Bit 7 bit in the DISMAP register.
  - Enable pins in bank X - Select yes/no to enable/disable one or more pins in bank X.
    This item modifies the DISX bit in the PCL1 register.
  - Enable pins in bank Y - Select yes/no to enable/disable one or more pins in bank Y.
    This item modifies the DISY bit in the PCL1 register.
Interrupts - Interrupts settings of the module
- Settings supported for HC908LB8 derivatives only.
  - Fault even interrupt - Fault even interrupt settings
    - Interrupt - Interrupt vector (for information only).
    - Fault interrupt - Enable/disable Fault even interrupt.
      This item modifies the FINT bit in the FSR register.
    - ISR name - Name of the interrupt service routine (ISR) invoked by this interrupt vector.
      The user code of the routine should handle all respective interrupt flags correctly.
- Settings supported for HC908MR8/MR32 derivatives only.
  - Fault even 1 interrupt - Fault even interrupt 1 settings
    - Interrupt - Interrupt vector (for information only).
    - Fault 1 interrupt - Enable/disable Fault even 1 interrupt.
      This item modifies the FINT1 bit in the FSR register.
    - ISR name - Name of the interrupt service routine (ISR) invoked by this interrupt vector.
      The user code of the routine should handle all respective interrupt flags correctly.
  - Settings supported for HC908MR8 derivatives only.
    - Fault even 2 interrupt - Fault even interrupt 2 settings
      - Interrupt - Interrupt vector (for information only).
      - Fault 2 interrupt - Enable/disable Fault even 2 interrupt.
        This item modifies the FINT2 bit in the FSR register
      - ISR name - Name of the interrupt service routine (ISR) invoked by this interrupt vector.
        The user code of the routine should handle all respective interrupt flags correctly.
    - Fault even 3 interrupt - Fault even interrupt 3 settings
      - Interrupt - Interrupt vector (for information only).
      - Fault 3 interrupt - Enable/disable Fault even 3 interrupt.
        This item modifies the FINT3 bit in the FSR register.
      - ISR name - Name of the interrupt service routine (ISR) invoked by this interrupt vector.
        The user code of the routine should handle all respective interrupt flags correctly.
  - Settings supported for HC908MR8 - 32 pins /32 derivatives only.
    - Fault even 4 interrupt - Fault even interrupt 4 settings
      - Interrupt - Interrupt vector (for information only).
      - Fault 4 interrupt - Enable/disable Fault even 4 interrupt.
        This item modifies the FINT4 bit in the FSR register.
      - ISR name - Name of the interrupt service routine (ISR) invoked by this interrupt vector.
        The user code of the routine should handle all respective interrupt flags correctly.
- PWM interrupt - PWM interrupt settings
  - Interrupt - Interrupt vector (for information only).
  - PWM interrupt - Enable/disable PWM interrupt.
    This item modifies the PWMINT bit in the PCTL1 register
  - ISR name - Name of the interrupt service routine (ISR) invoked by this interrupt vector.
    The user code of the routine should handle all respective interrupt flags correctly.
Initialization - Initialization options of the module
- Module enabled - Enable PWMMC module. This item modifies the PWMEN bit in the PCTL1 register

PROCESSOR EXPERT is trademark of Freescale Semiconductor, Inc.
Copyright 1997 - 2010 Freescale Semiconductor, Inc.