| Supported Targets | ESP32-P4 |
| ----------------- | -------- |

# Video LCD Display

This example is based on the [esp_video](https://github.com/espressif/esp-video-components/tree/master/esp_video) component and demonstrates how to display images from the camera on an LCD screen.

## How to use the example

## ESP-IDF Required

- This example supports ESP-IDF release/v5.4 and later branches. By default, it runs on ESP-IDF release/v5.4.
- Please follow the [ESP-IDF Programming Guide](https://docs.espressif.com/projects/esp-idf/en/latest/esp32/get-started/index.html) to set up the development environment. **We highly recommend** you [Build Your First Project](https://docs.espressif.com/projects/esp-idf/en/latest/esp32/get-started/index.html#build-your-first-project) to get familiar with ESP-IDF and make sure the environment is set up correctly.

### Prerequisites

* An ESP32-P4-Function-EV-Board.
* A 7-inch 1024 x 600 LCD screen powered by the [EK79007](https://dl.espressif.com/dl/schematics/display_driver_chip_EK79007AD_datasheet.pdf) IC, accompanied by a 32-pin FPC connection [adapter board](https://dl.espressif.com/dl/schematics/esp32-p4-function-ev-board-lcd-subboard-schematics.pdf) ([LCD Specifications](https://dl.espressif.com/dl/schematics/display_datasheet.pdf)).
* A MIPI-CSI camera powered by the SC2336 IC, accompanied by a 32-pin FPC connection [adapter board](https://dl.espressif.com/dl/schematics/esp32-p4-function-ev-board-camera-subboard-schematics.pdf) ([Camera Specifications](https://dl.espressif.com/dl/schematics/camera_datasheet.pdf)).
* A USB-C cable for power supply and programming.
* Please refer to the following steps for the connection:
    * **Step 1**. According to the table below, connect the pins on the back of the screen adapter board to the corresponding pins on the development board.

        | Screen Adapter Board | ESP32-P4-Function-EV-Board |
        | -------------------- | -------------------------- |
        | 5V (any one)         | 5V (any one)               |
        | GND (any one)        | GND (any one)              |
        | PWM                  | GPIO26                     |
        | LCD_RST              | GPIO27                     |

    * **Step 2**. Connect the FPC of LCD through the `MIPI_DSI` interface.
    * **Step 3**. Connect the FPC of Camera through the `MIPI_CSI` interface.
    * **Step 4**. Use a USB-C cable to connect the `USB-UART` port to a PC (Used for power supply and viewing serial output).
    * **Step 5**. Turn on the power switch of the board.

### Configure the Project

Run `idf.py menuconfig` and navigate to the `Example Configuration` menu, where you can configure the relevant pins and example-related options.

In the `Espressif Camera Sensors` Configurations, the camera sensor can be selected.

```
Component config  --->
    Espressif Camera Sensors Configurations  --->
        [*] SC2336  ---->
            Default format select for MIPI (RAW8 1280x720 30fps, MIPI 2lane 24M input)  --->
                (X) RAW8 1280x720 30fps, MIPI 2lane 24M input
```

### Build and Flash

Build the project and flash it to the board, then run monitor tool to view serial output (replace `PORT` with your board's serial port name):

```c
idf.py -p PORT flash monitor
```

To exit the serial monitor, type ``Ctrl-]``.

See the [ESP-IDF Getting Started Guide](https://docs.espressif.com/projects/esp-idf/en/latest/get-started/index.html) for full steps to configure and use ESP-IDF to build projects.