ADC: Analog to Digital Converter ADC_RegularConfig frequency of the clock to the ADC. The clock is common for all the ADCs. frequency of the clock to the ADC. The clock is common for all the ADCs. Resolution of the ADC conversion Select the alignment of the data stored after conversion. Enable or Disable the Continuous Conversion Mode Enable or Disable the Discontinuous Conversion Mode Enable/Disable DMA Continuous Requests Enable/Disable DMA Continuous Requests Enable/Disable DMA Continuous Requests Enable/Disable DMA Continuous Requests This parameter is used only when a DMA Request is configured. Else it is not relevant.<br> When the DMA Request for this ADC instance this parameter specifies whether the DMA requests are performed in one shot mode (DMA transfer stops when number of conversions is reached) or are performed in continuous mode (DMA transfer unlimited, whatever number of conversions).<br> Note: In continuous mode, DMA must be configured in circular mode. Otherwise an overrun will be triggered when DMA buffer maximum pointer is reached. Regular channel end of conversion selection Select the behaviour in case of overrun Specifies the usage of dynamic low power Auto Delay: New conversion start only when the previous conversion (for regular channel) is completed. Number of regular channels to be converted Number of regular channels to be converted The ADC is always powered off when not converting and automatically wakes-up when a conversion is started Enable/Disable the over sampling mode Configures the division coefficient for the Oversampler Configure the Oversampling ratio The regular triggered Oversampling mode Regular Channel x sampling time selection Regular Channel x sampling time selection Select the external event used to trigger the start of conversion of a regular group Select the external trigger polarity and enable the trigger of a regular group: When an external trigger is selected for ADC regular conversion, only the rising edge of the signal can start the conversion. Select the external trigger polarity and enable the trigger of a regular group: When an external trigger is selected for ADC regular conversion, only the rising edge of the signal can start the conversion. ADC trigger frequency mode must be set to low frequency when a duration is exceeded before ADC conversion start trigger event (between ADC enable and ADC conversion start trigger event or between two ADC conversion start trigger event). Set sampling time common to a group of channels. Set sampling time common to a group of channels. Set sampling time common to a group of channels. The rank in the regular group sequencer In Disabled, only the channel with the rank 1 is converted To have the Enabled choice in the Scan Conversion Mode : the Number Of Conversion has to be > 1 Configurable scan direction (Forward from channel 0 to 18 or Backward from channel 18 to channel 0) <br> Vbat = channel 14 <br> Vrefint = channel 13 <br> TempSensor = channel 12 ADC_RegularChannelRankConfig ADC_RegularChannelConfigForWD ADC_AnalogWDGConfig ADC_AnalogWDGConfigForAWD2 ADC_AnalogWDGConfigForAWD3 Enable/Disable Analog WatchDog Mode Number of used watchDogs. Configures the ADC analog watchdog mode. ADC channel for the analog watchdog Configures the ADC analog watchdog High threshold value. Configures the ADC analog watchdog High threshold value. Configures the ADC analog watchdog High threshold value. Configures the ADC analog watchdog High threshold value. Configures the ADC analog watchdog High threshold value. Configures the ADC analog watchdog Low threshold value. Specifies whether the analog watchdog is configured in interrupt mode or in polling mode. Enable/Disable Analog WatchDog2 Mode Number of used watchDogs. Configures the ADC analog watchdog High threshold value. Configures the ADC analog watchdog High threshold value. Configures the ADC analog watchdog High threshold value. Configures the ADC analog watchdog High threshold value. Configures the ADC analog watchdog Low threshold value. Specifies whether the analog watchdog is configured in interrupt mode or in polling mode. Enable/Disable Analog WatchDog3 Mode Number of used watchDogs. Configures the ADC analog watchdog High threshold value. Configures the ADC analog watchdog High threshold value. Configures the ADC analog watchdog High threshold value. Configures the ADC analog watchdog High threshold value. Configures the ADC analog watchdog Low threshold value. Specifies whether the analog watchdog is configured in interrupt mode or in polling mode. Select a watchdog to monitor the channel. Select a watchdog to monitor the channel. ADC channel for the analog watchdog ADC channel for the analog watchdog ADC_RegularChannelConfig ADC_CHANNEL_0 ADC_RegularChannelConfig ADC_CHANNEL_1 ADC_RegularChannelConfig ADC_CHANNEL_2 ADC_RegularChannelConfig ADC_CHANNEL_3 ADC_RegularChannelConfig ADC_CHANNEL_4 ADC_RegularChannelConfig ADC_CHANNEL_5 ADC_RegularChannelConfig ADC_CHANNEL_6 ADC_RegularChannelConfig ADC_CHANNEL_7 ADC_RegularChannelConfig ADC_CHANNEL_8 ADC_RegularChannelConfig ADC_CHANNEL_9 ADC_RegularChannelConfig ADC_CHANNEL_10 ADC_RegularChannelConfig ADC_CHANNEL_11 ADC_RegularChannelConfig ADC_CHANNEL_12 ADC_RegularChannelConfig ADC_CHANNEL_13 ADC_RegularChannelConfig ADC_CHANNEL_14 ADC_RegularChannelConfig ADC_CHANNEL_15 ADC_RegularChannelConfig ADC_CHANNEL_16 ADC_RegularChannelConfig ADC_CHANNEL_17 ADC_RegularChannelConfig ADC_CHANNEL_18 ADC_RegularChannelConfig ADC_CHANNEL_TEMPSENSOR ADC_RegularChannelConfig ADC_CHANNEL_VREFINT ADC_RegularChannelConfig ADC_CHANNEL_VBAT channelSelected channelSelected0 channelSelected channelSelected channelSelected channelSelected channelSelected channelSelected channelSelected channelSelected channelSelected channelSelected channelSelected channelSelected channelSelected channelSelected channelSelected channelSelected channelSelected channelSelected VtsATSelected$IpInstance channelSelected VrefTSelected$IpInstance channelSelected VbatfTSelected$IpInstance channelSelected RegularExternalTrigger $IpInstance_USED