Ivi.LxiSync.Interop

LxiSync root interface.

Pointer to the ILxiSyncArm interface.

Pointer to the ILxiSyncEventLog interface.

Pointer to the ILxiSyncEvents interface.

Pointer to the ILxiSyncTime interface.

Pointer to the ILxiSyncTrigger interface.

LxiSync arm interface.

Pointer to the ILxiSyncArmSources interface.

Specifies the number of times the arm has to occur to complete the arm loop; that is, the number of arms that are accepted before the measurement must be initiated again.

Specifies the delay from when the arm logic satisfied until the waiting for trigger state is entered. The units are seconds.

Pointer to the ILxiSyncArmAlarms interface.

LxiSync arm alarm interface.

This function configures the most commonly configured attributes of the arm alarm sub-system.

Enables or disables the arm alarm. Specifies the seconds part of 1588 time. Specifies the fractional part of 1588 time. Specifies the period of the arm alarm. Specifies the number of times to repeat the trigger at the period specified by the Arm Alarm Repeat Period attribute.

Specifies the seconds portion of time at which the alarm will go off.

Specifies the fractional portion of the time at which the alarm will go off.

Specifies the period of the arm alarm in seconds; that is, the amount of time in seconds that transpire before the alarm repeats.

Specifies the number of times to repeat the trigger at the period specified by the Arm Alarm Period attribute.

Enables or disables the arm alarm.

LxiSync repeated capability interface containing methods and properties that apply to all arm alarms defined for the device. A particular arm alarm can be accessed using the Item property.

This function disables all arm alarms.

This function creates a new arm alarm

Specifies the name of the arm alarm to create.

This function removes an arm alarm.

Specifies the name of the arm alarm to remove.

This function removes all of the custom arm alarms that were added using the Add Arm Alarm function.

The number of available arm alarms.

An interface reference pointer to the ILxiSyncArmAlarm interface which is selected by the alarm name.

The name of a alarm. It may be either a name returned by the Name property or a name mapped to a particular repeated capability in the session in the configuration store.

An interface reference pointer to the ILxiSyncArmAlarm interface which is selected by the alarm name.

The name of a alarm. It may be either a name returned by the Name property or a name mapped to a particular repeated capability in the session in the configuration store. An interface reference pointer to the ILxiSyncArmAlarm interface which is selected by the alarm name.

The alarm name for a given index.

One based index into the collection of alarms.

The alarm name for a given index.

One based index into the collection of alarms. The alarm name for a given index.

LxiSync arm source interface.

This function configures the most commonly configured attributes of the arm source sub-system.

Enables or disables the arm source. Specifies the style of the arm source.

Enables or disables the arm source.

Specifies the style of arm source detection.

Specifies a filter for restricting arm sources.

Specifies the LAN event identifier that is associated with this arm source. LAN Events with this identifier are accepted from the source described in the filter.

LxiSync repeated capability interface containing methods and properties that apply to all arm sources defined for the device. A particular arm source can be accessed using the Item property.

This function creates a new arm source.

Specifies the name of the arm source to create.

This function removes an arm source.

Specifies the name of the arm source to remove.

This function disables all arm sources.

This function removes all of the custom arm sources that were added using the Add Arm Source function.

The number of sources.

An interface reference pointer to the ILxiSyncArmSource interface which is selected by the source name.

The name of a source. It may be either a name returned by the Name property or a name mapped to a particular repeated capability in the session in the configuration store.

An interface reference pointer to the ILxiSyncArmSource interface which is selected by the source name.

The name of a source. It may be either a name returned by the Name property or a name mapped to a particular repeated capability in the session in the configuration store. An interface reference pointer to the ILxiSyncArmSource interface which is selected by the source name.

The source name for a given index.

One based index into the collection of sources.

The source name for a given index.

One based index into the collection of sources. The source name for a given index.

Enables or disables the OR-summing of the arm sources.

LxiSync event interface.

This function configures the most commonly configured attributes of the event sub-system.

Specifies the mode of the event. Specifies the signal which causes an event to be transmitted. Specifies a list of places to send the event. Specifies the slope of the event signal.

Specifies the signal which causes an event to be transmitted.

Specifies a list of places to send the event.

Specifies the slope of the inbound event that will cause the generation of an outbound event.

Specifies how this event is transmitted.

LxiSync event log interface.

This function removes all existing entries from the event log.

This function retrieves and clears the oldest event log entry for the IVI session.

Returns the number of event log entries available.

Enables or disables the event logging feature.

LxiSync repeated capability interface containing methods and properties that apply to all events defined for the device. A particular event can be accessed using the Item property.

This function disables all events.

This function creates a new event.

Specifies the name of the event to create.

This function removes an event.

Specifies the name of the event to remove.

This function removes all of the custom events that were added using the Add Event function.

The number of available events.

An interface reference pointer to the ILxiSyncEvent interface which is selected by the event name.

The name of an event. It may be either a name returned by the Name property or a name mapped to a particular repeated capability in the session in the configuration store.

An interface reference pointer to the ILxiSyncEvent interface which is selected by the event name.

The name of an event. It may be either a name returned by the Name property or a name mapped to a particular repeated capability in the session in the configuration store. An interface reference pointer to the ILxiSyncEvent interface which is selected by the event name.

The event name for a given index.

One based index into the collection of events.

The event name for a given index.

One based index into the collection of events. The event name for a given index.

Specifies whether the LXI device will serve as the wired-OR bias for specific LXI trigger bus lines.

LxiSync time interface.

This function retrieves the current 1588 time.

Indicates the seconds portion of the current 1588 time. Indicates the fractional portion of the current 1588 time.

Indicates if this device is the 1588 master.

Indicates if the device is synchronized.

LxiSync trigger interface.

Pointer to the ILxiSyncTriggerSources interface.

Specifies the number of times a trigger has to occur to complete a measurement; that is, the number of triggers that are accepted before the measurement must be armed again.

Pointer to the ILxiSyncTriggerAlarms interface.

Specifies which of the available trigger sources to use as the signal for triggering the device-specific operation (for example, a measurement).

LxiSync trigger alarm interface.

This function configures the most commonly configured attributes of the trigger alarm sub-system.

Specifies the seconds part of 1588 time. Specifies the fractional part of 1588 time. Specifies the period of the trigger alarm. Specifies the number of times to repeat the trigger at the period specified by the Trigger Alarm Repeat Period attribute.

Specifies the period of the trigger alarm in seconds; that is, the amount of time in seconds that transpire before the alarm repeats.

Specifies the number of times to repeat the trigger at the period specified by the Trigger Alarm Period attribute.

Specifies the fractional seconds portion of the time at which the alarm will go off.

Specifies the seconds portion of the time at which the alarm will go off.

Enables or disables the trigger alarm.

LxiSync repeated capability interface containing methods and properties that apply to all trigger alarms defined for the device. A particular trigger alarm can be accessed using the Item property.

This function creates a new trigger alarm

Specifies the name of the trigger alarm to create.

This function disables all trigger alarms.

This function removes a trigger alarm.

Specifies the name of the trigger alarm to remove.

This function removes all of the trigger alarms that were added using the Add Trigger Alarm function.

Returns the number of currently available trigger alarms.

An interface reference pointer to the ILxiSyncTriggerAlarm interface which is selected by the alarm name.

The name of a alarm. It may be either a name returned by the Name property or a name mapped to a particular repeated capability in the session in the configuration store.

An interface reference pointer to the ILxiSyncTriggerAlarm interface which is selected by the alarm name.

The name of a alarm. It may be either a name returned by the Name property or a name mapped to a particular repeated capability in the session in the configuration store. An interface reference pointer to the ILxiSyncTriggerAlarm interface which is selected by the alarm name.

Returns the physical repeated capability identifier defined by the specific driver for the trigger alarm that corresponds to the one-based index that the user specifies

One based index into the collection of alarms.

Returns the physical repeated capability identifier defined by the specific driver for the trigger alarm that corresponds to the one-based index that the user specifies

One based index into the collection of alarms. Returns the physical repeated capability identifier defined by the specific driver for the trigger alarm that corresponds to the one-based index that the user specifies

LxiSync trigger source interface.

This function configures the most commonly configured attributes of the trigger source sub-system.

Specifies the trigger source delay. The units are seconds. A negative value implies pre-trigger acquisition. Specifies the slope of the trigger source.

Specifies the trigger source delay from when the trigger logic is satisfied until the device specific action (for instance a measurement) is triggered.

Specifies the slope of the trigger source.

Specifies the LAN event identifier that is associated with this trigger source.

Specifies a filter for restricting trigger sources.

LxiSync repeated capability interface containing methods and properties that apply to all trigger sources defined for the device. A particular trigger source can be accessed using the Item property.

This function creates a new trigger source.

Specifies the name of the trigger source to create.

This function removes a trigger source.

Specifies the name of the trigger source to remove.

This function removes all of the custom trigger sources that were added using the Add Trigger Source function.

The number of sources.

An interface reference pointer to the ILxiSyncTriggerSource interface which is selected by the source name.

The name of a source. It may be either a name returned by the Name property or a name mapped to a particular repeated capability in the session in the configuration store.

An interface reference pointer to the ILxiSyncTriggerSource interface which is selected by the source name.

The name of a source. It may be either a name returned by the Name property or a name mapped to a particular repeated capability in the session in the configuration store. An interface reference pointer to the ILxiSyncTriggerSource interface which is selected by the source name.

The source name for a given index.

One based index into the collection of sources.

The source name for a given index.

One based index into the collection of sources. The source name for a given index.

Defined values for the slope of the event that is inbound to the event subsystem that will cause the generation of an outbound event

The event will be transmitted with a rising edge.

The event will be transmitted with a falling edge.

Defined values for the style of arm source detection.

Configures the LXI device to arm on the rising edge of the arm source.

Configures the LXI device to arm on the falling edge of the arm source.

Configures the LXI device to arm while the arm source is high, that is, while it remains true.

Configures the LXI device to arm while the arm source is low, that is, while it remains false.

Event driver mode.

Enables the event in driven mode.

Disables the event.

Enables the event in wired-OR mode.

Defined values for the Trigger Source attribute.

Configures the LXI device to trigger on the rising edge of the trigger source.

Configures the LXI device to trigger on the falling edge of the trigger source.